Aprilia Tuareg 660 · Home manual

Home edition · A5 booklet · Complete edition: everything in the travel edition, plus service intervals, trip preparation, tools and packlist, workshop-only jobs, the bike record and source notes.

For the 2022+ Tuareg 660. Sources appear once, in the data tables: OM = owner's manual page, WS = workshop manual page, 3P = third-party, not in the Aprilia manuals (verify). Procedures follow the Aprilia manuals; where Aprilia gives none (tyre plug, chain link, jump start) they follow standard motorcycle practice.

Contents

  1. Data
  2. Daily check
  3. Tyres & wheels
  4. Drive chain
  5. Brakes
  6. Oil, coolant, air filter
  7. Battery, fuses, lights
  8. Suspension & clutch
  9. Fault finding
  10. Service & trip preparation
  11. Tools & packlist
  12. My bike & sources

Data

Tyres & wheels

FrontRearSrc
Tyre90/90-21 M/C 54V150/70 R18 M/C 70VOM 182
Permitted alternative (max 170 km/h)90/90-21 54R M+S150/70-18 70R M+SOM 182
Rim (spoked, tubeless)2.15 × 21"4.25 × 18"OM 182
Pressure cold · solo2.0 bar · 29 psi2.5 bar · 36 psiOM 182
Pressure cold · 2-up2.2 bar · 32 psi2.7 bar · 39 psiOM 182
Pressure cold · off-road2.0 bar · 29 psi2.0 bar · 29 psiOM 183
Min. tread2 mm, or the local legal minimumOM 142
Puncture limitReplace the tyre if the hole in the tread is larger than 5 mmOM 141
Rim runout max.0.8 mm radial and axialWS 169

Fluids & capacities

FluidSpecQtySrc
Engine oilSAE 10W-50 synthetic, API SL, JASO MA22.3 L¹OM 178, 191
CoolantReady-mixed red ethylene-glycol antifreeze, organic inhibitors (OAT)2.0 ± 0.2 LOM 178, 191
Brake fluidDOT 4—OM 191
FuelUnleaded 95 RON, max E1018 L, reserve 2.7OM 108
Chain lubeSpray lube safe for sealed (O-ring) chains—OM 174
Fork oilSAE 7.5W—OM 191
GreaseLithium-calcium, EP, water-repellent—OM 191

¹ Oil change including filter. The workshop procedure says 2.7 L (WS 40), apparently copied from the RS 660. Fill 2.3 L, then top up to MAX on the dipstick.

Torques & tool sizes

FastenerNmToolSrc
Front axle6517 mm hexWS 8 · tool 3P
Front axle pinch screws ×2105 mm hex or 10 mm²WS 9 · tool 3P
Front caliper screws M10 ×45013 mmWS 9 · tool 3P
Rear axle nut M20×1.512026 mm3P
Chain adjuster lock nut / bolt—10 + 13 mm3P
Oil drain plug, new washer20—3P
Mirror bases50—WS 11
Handguard screws4—WS 10
Anything else: M5 · M6 · M8 · M10 · M125.5 · 9.5 · 25 · 50 · 80—WS 27

² The aftermarket tool kits disagree; check your bike. Screws with pre-applied threadlocker must be replaced once loosened (WS 28).

Limits, settings & parts

ItemValueSrc
Chain slack≈ 48 mm total, 320 mm in front of the rear axle, side standOM 172
ChainRegina 520 ZRA, 120 links, riveted master link · sprockets 15/42OM 179
Chain wear, 8 pitches tautnew 127.0 mm · replace at ≥ 130.8 mm (3 %)WS 201 · mm calc.
Brake padsReplace at ≈ 1.5 mm friction material, all pads on that axleOM 165
Brake disc min. thicknessfront 4.0 mm · rear 4.5 mmWS 245, 247
Rear pedal free play1.5 mmWS 54
Idle speed1400 ± 100 rpmOM 176
BatteryBS BSLi-04 lithium, 12 V 48 Wh · alternative Yuasa YT12A-BS lead-acidOM 183
Charging voltageNever above 15 VWS 117
Spark plugNGK IR MR9DI-7, gap 0.7-0.8 mmOM 183
Oil filterOEM 857187 · Hiflofiltro HF1383P
Due on the roadOil + filter 10 000 km / 12 months · chain check 1000 km · off-road: halve chain and air filterOM 188

Suspension settings

Fork capsseen from the rider's seat 1123 LEFTRIGHT Clockwise = closedharder damping,more preload Rear shockseen from behind 456 bike's left ←→ right
#AdjusterSoloLoaded
1Fork preload, nut on both legs (set equal)6 mm out7 mm out
2Fork compression, left cap8 clicks out3 clicks out
3Fork rebound, right cap8 clicks out7 clicks out
4Shock preload knob, left10 clicks in from fully open26 clicks in
5Shock compression, reservoir, right2 turns out2 turns out
6Shock rebound, bottom of shock, right1.5 turns out1 turn out

OM 110-116 · "out" = counted from fully clockwise (closed) · loaded = passenger and/or luggage

Where things are

1234567 LEFT sidefront ← 891011121314 RIGHT side→ front
Positions approximate. Numbers match the table.
#WhatWhere · accessSrc
1Battery, auxiliary fusesUnder the rider seat. Passenger seat off first, then rider seat; battery cover 2 screwsOM 21, 149, 155
2Main fuse 30 A + spareBehind the left side panel: 4 screws, unhook the front, unplug the connectorOM 21, 158
3Seat lockIgnition key clockwise; press the seat's middle-rear, lift and slide backOM 22, 98
4Coolant expansion tankLeft side, under the steering headOM 144
5Shock preload knobLeft side, top of the shockOM 111
6USB socket 5 V, 1 ALeft of the dashOM 99
7Sump guardUnder the engine: 2 front screws, then 2 rearOM 22 · WS 292
8Front brake reservoirRight handlebar; cover 2 screwsOM 22, 146
9Oil filler cap + dipstickRight side of the engineOM 22
10Oil filterRight side, front of the engine, lowOM 22
11Rear brake reservoir · shock compression adjusterRight side, next to the shock; reservoir screw capOM 22, 111, 147
12Shock rebound adjusterRight side, bottom of the shock at the linkageOM 112
13Air filterUnder the fuel-tank upper cover; airbox cover 4 screwsOM 22 · WS 41
14Rear brake pedalFree-play adjuster behind the right frame coverOM 22 · WS 54
Clutch cable in-line adjusterRight side of the bikeWS 55
Frame / engine numberFrame crossbar under the seat / rear of the crankcase near the shockOM 100

Daily check

  • Tyres: pressure (cold), cuts, embedded objects, tread.
  • Spokes: tap each with a screwdriver. Even ring = OK; a dull note = loose.
  • Brakes: lever and pedal feel, fluid level, pads, leaks.
  • Oil level (warm, upright) · coolant level (cold).
  • Chain: slack, lube, no tight spots.
  • Throttle snaps back · clutch free play, cable not frayed.
  • Steering free lock to lock, no play, no notches.
  • Side stand springs back; the engine cuts if you select a gear with it down.
  • Fasteners: axles, calipers, racks, sump guard, mirrors.
  • Lights, horn, indicators, brake light; warning LEDs light for 3 s at key-ON.
  • ABS tone wheels clean (mud causes ABS/ATC faults) · fuel, cap locked.

Dust or off-road: check the air filter every few days and the chain daily.

Tyres & wheels

Tubeless puncture plug

  1. Find the leak (soapy water), mark it, pull the object out.
  2. Ream the hole, several strokes.
  3. Load a string plug in the needle (cement if supplied). Push in until ⅓ is left outside, pull the needle straight out.
  4. Trim to about 5 mm, inflate, leak-test.
  5. Ride gently and keep checking the pressure. A plug gets you home: have the tyre repaired properly or replaced.

Front wheel out & in

exploded · seen from behind, rider's left on the left 123456
  1. Axle, 17 mm hex: in and out on the left
  2. Left fork leg: pinch clamp, 2 screws
  3. Left spacer
  4. Hub, a disc each side; ABS tone ring on the right
  5. Right spacer
  6. Right fork leg: the axle threads in here
  1. Lift the front wheel: jack under the sump guard, bike strapped so it can't tip.
  2. Remove both calipers (2 screws each) and hang them up. Don't pull the brake lever while they are off.
  3. Loosen the 2 pinch screws (2), unscrew the axle (1) and pull it out to the left.
  4. Take the wheel out. The spacers (3, 5) come loose: keep each with its side.
  5. Refit: wheel with both spacers, axle from the left. Tighten the axle to 65 Nm first, then the pinch screws to 10 Nm.
  6. Calipers 50 Nm. Pump the lever until firm, spin the wheel.

Rear wheel out & in

exploded · seen from behind, rider's left on the left swingarm swingarm 12345678910
  1. Nut 26 mm + washer
  2. Left adjuster block
  3. Outer spacer, in the sprocket carrier
  4. Sprocket carrier + sprocket (comes out with the wheel)
  5. Inner spacer, between carrier and hub flange
  6. Cush rubbers in the hub flange
  7. Hub; disc and ABS tone ring on the right
  8. Right spacer
  9. Right adjuster block
  10. Axle: in and out on the right
  1. Rear stand, or the sump guard on a solid block so the wheel hangs free.
  2. Both sides: loosen the adjuster lock nuts and back the adjusters off.
  3. Remove the axle nut and washer (1).
  4. Support the wheel and pull the axle (10) out to the right; the adjuster blocks (2, 9) come free.
  5. Push the wheel forward, lift the chain off the sprocket and roll the wheel out; the disc slides out of the caliper. Don't press the brake pedal while the wheel is out. Keep the loose spacers (3, 5, 8) with the wheel.
  6. Refit: cush rubbers (6), inner spacer (5), carrier (4) and both outer spacers (3, 8) in place. Wheel in, disc between the caliper pads, chain on.
  7. Axle in from the right with the right adjuster block; then the left block, washer and nut, finger-tight.
  8. Set the chain slack (next chapter), tighten the lock nuts, then the axle nut to 120 Nm.
  9. Pump the brake pedal, spin the wheel, recheck the slack.

Drive chain

Check slack

320 mm ≈ 48 mm total rear axle front
  1. Engine off, side stand, neutral.
  2. At 320 mm in front of the rear axle, push the bottom run up, then pull it down. Total travel ≈ 48 mm.
  3. Roll the bike and repeat at several points. If the slack varies, links are kinked or seized: replace the chain.

Adjust

AlignedMisaligned aa a₁a₂ same distance both sideschain runs crooked, wears fast
Seen from above, front at the top. a = adjuster block to the rear end of the swingarm.
  1. Rear stand. Loosen the axle nut, then the lock nuts on both sides.
  2. Turn both adjuster bolts by the same amount. Keep the marks level on both sides and measure that the block-to-swingarm-end distance is the same left and right.
  3. Tighten both lock nuts, then the axle nut to 120 Nm.
  4. Recheck on the side stand. Never set it tighter than spec: the chain tightens as the suspension compresses.

Clean, lube, repair

  • Clean & lube: light water jet, chain cleaner (no petrol or harsh solvents: they kill the O-rings), let it dry, spray the inside of the lower run, let it set. After every wash and after rain.
  • Worn (limit in the Data table), damaged rollers, loose pins, missing O-rings or hooked teeth: replace chain and both sprockets together.
  • Broken chain: fit a 520 master link (a clip link gets you home, a rivet link is permanent) with a chain breaker/riveter. Don't over-press the side plate; the link must move freely.

Brakes

Fluid level & top-up

  • Front: turn the bars until the reservoir is level and read the sight glass. Top up: 2 screws, cover, gasket.
  • Rear: bike upright; screw cap and gasket off; top up with a syringe to between MIN and MAX.
  • With worn pads, top up only to just above MIN, or it will overflow when new pads push the pistons back.
  • DOT 4 absorbs water and strips paint: close it quickly, cover nearby paint. A slow fall is pad wear; a sudden drop is a leak.

Pads

Pad backingplate Replace at ≈ 1.5 mm friction material only,not the backing plate, or when the weargroove has gone Disc Minimum front 4.0 mmrear 4.5 mm thinnest point,measure several
  1. Pull the split pin, slide out the pad pin, take out the pads.
  2. Don't touch the lever or pedal while the pads are out.
  3. Clean the pistons and push them back gently; watch the reservoir level.
  4. New pads, pad pin, new split pin. Pump until firm before riding.
  5. Brake gently for the first ~100 km to bed them in.

Front: always replace the pads in both calipers together.

Bleeding

  1. Pumpthe lever or pedal several times, then hold it
  2. Openthe bleed nipple ¼ turn
  3. Closeit before the lever bottoms
  4. Releasethe lever
  • Bike level, clear hose from the nipple into a bottle. Keep the reservoir above MIN the whole time.
  • Repeat until no bubbles come out. Front: bleed both calipers. Then top up and refit the caps.
  • Still spongy: air is trapped in the ABS unit, which needs the dealer's diagnostic tool.

Lever & pedal

  • Front lever reach: push the lever forward and turn the adjuster; anticlockwise brings it closer.
  • Rear pedal free play: remove the right frame cover, loosen the lock nut, turn the pushrod pin, re-lock.

Oil, coolant, air filter

Oil level

  1. Engine warm from about 15 km of riding (not idling). Switch off and wait a few seconds.
  2. Level ground, bike upright on both wheels, not on the side stand.
  3. Unscrew the dipstick, wipe it, put it back without screwing it in, pull it out and read.
  4. Aim for about MAX. Never below MIN or above MAX. Top up only with the specified oil.

Oil & filter change

  1. Warm engine. Remove the sump guard (2 front screws, then 2 rear while supporting it).
  2. Container of at least 3 L underneath. Drain plug out, then the filler cap; let it drain for several minutes.
  3. Unscrew the old filter. Oil the new filter's seal, pre-fill it about ⅓, screw it in by hand.
  4. Drain plug with a new aluminium washer, 20 Nm.
  5. Fill 2.3 L, run the engine a few minutes, switch off, wait 30 s, top up to MAX.
  6. Check the plug and filter for leaks, refit the sump guard.

Coolant

  • Check cold, bike upright: the level must be between MIN and MAX. Don't ride below MIN.
  • Top up through the expansion tank cap to halfway between MIN and MAX.
  • Never open it hot: the system is pressurised.
  • No coolant to hand: clean water gets you to a workshop. Replace it with the correct mix soon, especially if frost is possible.

Air filter (dust)

Remove the fuel-tank upper cover and the 4 airbox cover screws, lift out the filter. It is paper: tap it out gently from the clean side; never wash or oil it. Replace it if it stays clogged.

Battery, fuses, lights

Battery

  • Remove: key OFF, seats off, cover off. Disconnect − first, then +. Refit + first, then −, with a little grease on the terminals.
  • TEST button on the battery: 5-6 bars ready · 3-4 charge recommended · 1-2 charge needed · 0 faulty.
  • Cold: the lithium battery works from 0 to 40 °C. Below 0 °C, make short repeated start attempts; each one warms it. For long use outside that range fit the lead-acid alternative.
ChargingNormalQuick
Lithium (standard)2.0 A · 2 h8 A · 0.5 h
Lead-acid (alternative)1.0 A · 8-10 h10 A · 1 h

OM 152-153

Use a lithium charger, or a plain 12 V charger with no desulphation or pulse mode, never above 15 V. Stop if the battery gets warm.

At rest, 1-2 h after charging chargeOK Engine running, ≈ 5000 rpm low: not chargingnormal faulty 1212.41313.51414.515V

Jump start: donor car's engine off. + to +, then − to bare metal on the engine or frame. Start, disconnect in reverse order. Never use a booster above 15 V.

Fuses

Key OFF. Check the smallest ratings first and the main fuse last. Replace only with the same rating, and find the cause: a fuse that blows again means a short. Pulling the main fuse resets the clock and trip.

H15I5J7.5K7.5L5M20 A5B7.5C5D7.5E5F5G2 spares below (N)spares below (N) Under the rider seat · rating in A
Colours follow the standard blade-fuse code. The box with the blue 15 A and yellow 20 A fuses is H-M. Main fuse O (30 A) is separate, behind the left side panel.
FuseACircuit
A5Running lights, number-plate light, horn
B7.5Instrument panel, indicators, heated grips
C5Key-on: ECU, ABS, dash, left switches, starter relay
D7.5ECU permanent feed
E5Key-on: AMP, OBD, anti-theft
F5Headlamp
G2USB socket
H15Engine: fan relay, ECU, fuel pump relay, lambda, injectors, coils, air valve
I5Anti-theft provision, OBD
J / K7.5Right / left radiator fan
L5Fog lights (if fitted)
M20ABS
O30Main: battery charging, everything

OM 156-159 · A-M under the rider seat, O behind the left side panel

Lights & headlight aim

All lights are LED: no bulbs to carry, a failed module means a new unit.

Aim (after loading luggage): bike 10 m from a wall on level ground, rider seated, low beam on. The cut-off should sit at 0.9 × the headlight's height above the ground: headlight at 90 cm → cut-off at 81 cm.

Low beam: two adjusters behind the fairing (left and right), clockwise lowers. High beam: Phillips screw underneath, clockwise raises.

Suspension & clutch

Adjusting the suspension

Settings and adjuster positions: see Suspension settings in the Data chapter. Turn each adjuster fully clockwise first, then count out. Never force an adjuster past its stop, set both fork legs the same, and add rebound damping when you add preload.

Clutch

Adjust if it slips, drags (the bike creeps or stalls in gear) or bites too late.

  • Fine: the adjuster at the lever; clockwise increases free play.
  • Coarse: the in-line adjuster on the right side; loosen the nut, turn, re-lock.
  • Test: engine running, 1st gear, clutch pulled: no creep, no stall. No slip under acceleration.

Fault finding

Won't start

Dash lights at key-ON?
No → battery terminals · TEST button · main fuse O · key
yes ↓
Starter turns?
No → kill switch at RUN · neutral, or clutch pulled with the stand up · brake held · side-stand switch (its pin must sit in the stand's hole) · fuse C · battery charge
yes ↓
Engine fires?
No → fuel · fuel pump buzzes at key-ON? If not, fuse H · immobilizer asking for the user code · cold lithium battery: short repeated attempts
yes ↓
Dies when you select a gear?
Yes → side stand still down, or its switch is faulty

Dashboard alarms

MessageAction
ALARM OIL PRESSURE, flashingStop the engine now. Check the oil level; don't ride on.
ALARM OIL SENSOR, steadySensor fault. Check the level; dealer soon.
Temperature flashingOverheating (115 °C): stop, cool down, see Other faults.
ALARM URGENT SERVICE, fast flashLimp mode (less torque, fixed idle, or about 3000 rpm). Ride gently to a dealer.
ALARM SERVICEStored fault; dealer when practical.
ALARM CAN ECU DISCONNECTEDHazards flash until you signal right. Pull over; check fuses C and D.
ALARM CAN BUS OFF / CAN HLUWiring fault (HLU = headlamp). Ride carefully to a dealer.
ATC alarmTraction control off. Clean the tone wheels and sensors.
BRAKE STUCKA brake has been on for over 30 s: foot on the pedal, or a sticking lever or pedal.
Code requestImmobilizer fault: enter your 5-digit user code to start.

OM 33-37, 97

Other faults

SymptomCheck
OverheatingCoolant level (cold) · both fans running, else fuses J/K, H · radiator blocked with mud: rinse from behind, low pressure
Battery warningTerminals tight and clean · measure the voltage (scale under Battery)
ABS / ATC light after mudClean tone wheels and sensors, cycle the ignition. If it stays on, ABS is off: brake gently.
Spongy brakeFluid level, leaks, then bleed. After a long descent: let it cool, use engine braking.
Clutch slips or dragsAdjust free play; cable frayed or kinked?
Vibration, weaveTyre pressure, loose spokes, axles, chain tight spots, wheel bearings, steering-head play, luggage too high or too far back
No lights or hornFuses A, F, B

After a drop

  • Fuel and oil leaks · levers, pedals and pegs (bend back slowly) · bar alignment.
  • Side-stand switch and spring · radiator and hoses · mirror and handguard bolts.
  • Stand it upright a minute or two before restarting, then check the oil level.
  • Recovery: transport upright, strapped, in 1st gear, mirrors folded. Aprilia advises against towing.

Service & trip preparation

Service intervals

OM 188-190 · whichever comes first, km or months · ★ halve off-road

R replace   I inspect   A adjust   L lubricate

km × 1000 →11020304012 mo24 mo
Engine oil, oil filter, drain-plug washerRRRRRRR
Air filter ★IRIR
Spark plugsRR
Valve clearanceAA
Drive chain ★ILILILILILII
Sprockets, chain slider, rollerIIII
Clutch cable ★LLLLLLL
Brake pads and discsIIIIIII
Brake fluidIIIIIIR
CoolantIIIIIIR
Cooling systemIIII
TyresIIIIIII
Wheel bearings ★ · steering bearingsIIIIIII
Shock bearings and linkage ★IIII
Fork seals ★IIIIR
Fork oil ★ (or 4 years)R
Headlight aimIIII
Nuts and bolts ★IIIII
Diagnosis with dealer toolIIIIIII

Also at the dealer: O-rings, gaskets and safety switches as listed in OM 189-190. Chain: check every 1000 km between services.

Before the trip

  • Any service due during the trip? Do it before: oil and filter, chain and sprockets, pads, tyres, brake fluid and coolant age.
  • Dry run: remove both wheels and the front pads using only the travel kit. Note every size that didn't fit.
  • Check the drain plug: some 2022-build bikes have the wrong one, which seals only with stacked washers. Correct: OEM 1A012848 with washer 831393 (3P).
  • Set your own immobilizer user code (default 00000, dash menu 6.2) and keep it off the bike. Spare key separate from the bike key.
  • Charge the battery; terminals clean and tight.
  • Fill in My bike: pinch-screw size, drain-plug and bleed-nipple sizes, fuse type.
  • Paint-pen marks across the axle nuts after torquing.
  • Set the suspension for the load, re-aim the headlight.
  • Save the travel PDF and HTML on your phone for offline use. List dealers along the route.

Workshop jobs (not roadside)

  • Spark plugs: fuel tank and complete airbox must come off (WS 37).
  • Valves: bucket tappets with shims 1.75-3.15 mm in 0.025 mm steps (WS 49).
  • Steering head: special tool AP8140190; ring nut 60 Nm, back off, 40 ± 5 Nm; 250 ± 100 g pull at the grip end to turn the bars (WS 148-150).
  • ABS bleeding, fork oil and seals, wheel and steering bearings: dealer.

Engine & chassis data

Engine659 cc parallel twin, DOHC, 4 valves/cyl, 81 × 63.93 mm, CR 13.5:1, wet sump, cartridge oil filter
ChassisSteel double-cradle frame, rake 26.7°, wheelbase 1525 mm, kerb weight 204 kg
Suspension43 mm USD fork, 240 mm travel · linkage shock with piggyback
BrakesFront 2 × Ø300 mm, 2-piston floating calipers · rear Ø260 mm, 1-piston · ABS
Electrical360 W generator · main fuse 30 A

OM 176-184

Washing & storage

  • Engine cold, low-pressure water only. No pressure washer or steam on the seat, electrics, bearings, chain or plastics. Afterwards: test the brakes, lube the chain, levers, pedals, clutch cable and locks (OM 166-170).
  • Parked more than 15 days: pull the main fuse or remove the battery and recharge it monthly (OM 153).

Tools & packlist

On the bike, always

  • 17 mm hex bit (front axle) · 26 mm low-profile socket (rear axle)
  • 3/8" ratchet, short extension, breaker bar or tube extension for 120 Nm
  • 1/4" bit driver · hex 3, 4, 5, 6, 8 mm · Torx T20, T25, T27, T30, T40, T45, T50 · PH1, PH2 · flat 6 mm
  • Sockets 8, 10, 12, 13, 14, 17 mm · combination spanners 8, 10, 12, 13, 14, 17, 19 mm
  • Needle-nose pliers (split pins), side cutters, small adjustable spanner
  • Short cross-head screwdriver (front brake reservoir) · knife or multitool
  • Tubeless plug kit · CO₂ inflator + 4 cartridges or 12 V mini compressor
  • Digital tyre gauge · valve-core tool + 2 cores
  • Spare fuses 2, 5, 7.5, 15, 20, 30 A (your fuse type) · spare split pins
  • Cable ties, tape, 2 hose clamps, wire, small bag of M5/M6/M8 bolts and nuts
  • Gloves (nitrile + work), rag, headlamp torch, paint pen

Add for long or remote trips

  • Torque wrench 20-120 Nm (3/8") · torque driver 2-25 Nm (1/4")
  • Chain breaker/riveter for 520 · 30 cm steel ruler
  • Bleed kit: clear hose, small bottle, syringe · ring spanner for the bleed nipples
  • Oil change: filter wrench, funnel, folding container ≥ 3 L
  • Tyre levers ×3, bead breaker, rim protectors
  • Multimeter · lithium jump pack (≤ 15 V) or jump leads
  • Crimp connectors, crimper, electrical tape, contact cleaner
  • Epoxy putty, medium threadlocker, grease sachet
  • Collapsible lift stand or jack, or a block + ratchet strap
  • Fork-seal cleaning tool (e.g. Seal Mate)

Spares

  • Front pads (both calipers) + rear pads
  • 520 master links: 1 clip, 1 rivet
  • Clutch and front brake lever
  • Clutch cable
  • Oil filter + 2 drain washers
  • Air filter (dusty routes)
  • Tubeless valve · optional 21" emergency tube
  • Spare key, carried separately

Consumables

  • 1 L 10W-50 JASO MA2
  • 250 ml DOT 4, sealed
  • 0.5 L ready-mixed red OAT coolant
  • O-ring-safe chain lube
  • Chain cleaner
  • Hand cleaner, wipes

Very long trips: book tyres, a chain kit and oil filters in advance with dealers along the route.

My bike & sources

My bike

Frame no. (VIN) · engine no.
Plate · insurance · assistance tel.
Pinch screws: 5 mm hex or 10 mm?
Drain plug · bleed nipple sizes
Fuse type (mini / standard blade)
Last oil change (km · date)
Chain + sprockets fitted (km)
Tyres fitted (km · model)
Brake fluid · coolant changed
Next service due (km)

Sources & conflicts

  • Aprilia: owner's manual Ed. 01_10/2021 (2Q000498, OM) and service station manual 2Q000524 (WS).
  • Third-party (3P): rear axle 120 Nm and drain plug 20 Nm from published torque lists (maintenanceschedule.com); tool sizes from Tuareg 660 kits by Eastbound, Obsidian and Tusk; oil filter cross-reference from maintenanceschedule.com; drain-plug issue from AF1 Racing.
  • Oil capacity: spec tables 2.3 L (OM 178, WS 25); WS 40 procedure 2.7 L. 2.3 L matches the Tuareg's shallower sump.
  • Shock settings: WS 158 differs from OM 113 and appears to come from another model; the OM values are used.
  • Pinch clamp side: WS 165 says left fork leg, WS 173 says right; photos and WS 8 show the clamp on the axle-head side (left).
  • Not in your manual edition: rear axle, sprocket, disc and caliper-bracket torques ("prescribed torque" only).

Aprilia may revise specs; your dealer has the latest data. Use at your own risk.

↑ Top